Eaton HCM1A1104V2-2R2-R 2.2 uH Shielded Automotive Inductor
Eaton HCM1A1104V2-2R2-R 2.2 uH Shielded Automotive Inductor

Eaton HCM1A1104V2-2R2-R 2.2 uH Shielded Automotive Inductor

Share
Eaton HCM1A1104V2-2R2-R: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 10.5 A Irms, Isat 16 A, DCR 6 mOhm, 11.2 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1104V2-2R2-R 2.2 uH Shielded Automotive Inductor

    HCM1A1104V2-2R2-R at a glance: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 10.5 A Irms, Isat 16 A (20% rolloff @ +25 °C), DCR 6 mOhm, 11.2 x 10.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1104V2-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.41 uH
    Irms (DC, 40 °C rise)10.5 A
    Isat (20% rolloff @ +25 °C)16 A
    DCR typical @ +20 °C6 mOhm
    DCR maximum @ +20 °C7 mOhm
    SRF typical25 MHz
    K-factor (Bp-p = K x L x dI)432, Bp-p in Gauss
    Package11.2 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10903

    Mechanical Drawing

    HCM1A1104V2-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10903: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    With 6 mOhm typical, the I-squared-R loss at the full 10.5 A rating is about 0.661 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 282 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 432 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 950 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 25 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1104V2 line-up this part is number 9 of 19 by inductance, between 0.2 uH and 68 uH.

    One step down the table, HCM1A1104V2-1R5-R, sits at 1.5 uH with 14 A and 3.8 mOhm – the lower inductance buys about 5.8 A of extra current in the same body.

    • Core material: alloy powder core, 11.2 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 7 mOhm becomes roughly 10.7 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products