Eaton HCM1A1104V2-R90-R AEC-Q200 Inductor 0.90 uH, Isat 22 A
Eaton HCM1A1104V2-R90-R AEC-Q200 Inductor 0.90 uH, Isat 22 A

Eaton HCM1A1104V2-R90-R AEC-Q200 Inductor 0.90 uH, Isat 22 A

Share
Eaton HCM1A1104V2-R90-R: AEC-Q200 automotive power inductor, 0.90 uH ±20%, 20 A Irms, Isat 22 A, DCR 2.17 mOhm, 11.2 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1104V2-R90-R AEC-Q200 Inductor 0.90 uH, Isat 22 A

    HCM1A1104V2-R90-R at a glance: AEC-Q200 automotive power inductor, 0.90 uH ±20%, 20 A Irms, Isat 22 A (20% rolloff @ +25 °C), DCR 2.17 mOhm, 11.2 x 10.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1104V2-R90-R
    OCL (open circuit inductance)0.90 uH ±20%
    FLL minimum, at Isat0.58 uH
    Irms (DC, 40 °C rise)20 A
    Isat (20% rolloff @ +25 °C)22 A
    DCR typical @ +20 °C2.17 mOhm
    DCR maximum @ +20 °C2.5 mOhm
    SRF typical49 MHz
    K-factor (Bp-p = K x L x dI)361, Bp-p in Gauss
    Package11.2 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10903

    Outline Drawing

    HCM1A1104V2-R90-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10903: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 0.868 W from a typical DCR of 2.17 mOhm at 20 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 218 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 361, a peak-to-peak ripple of one amp produces roughly 325 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 49 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1104V2 family this is value 6 of 19, in a range that runs from 0.2 uH to 68 uH.

    One step down the table, HCM1A1104V2-R56-R, sits at 0.56 uH with 22.5 A and 1.56 mOhm – the lower inductance buys about 3.5 A of extra current in the same body.

    • Core material: alloy powder core, 11.2 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 2.5 mOhm becomes roughly 3.83 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the qualification file covers the module-level test plan.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message