Eaton HCM1A1104V3-680-R 68 uH AEC-Q200 Inductor, 2.2 A
Eaton HCM1A1104V3-680-R 68 uH AEC-Q200 Inductor, 2.2 A

Eaton HCM1A1104V3-680-R 68 uH AEC-Q200 Inductor, 2.2 A

Share
Eaton HCM1A1104V3-680-R: AEC-Q200 automotive power inductor, 68 uH ±20%, 2.2 A Irms, Isat 3 A, DCR 190 mOhm, 11.2 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1104V3-680-R 68 uH AEC-Q200 Inductor, 2.2 A

    HCM1A1104V3-680-R at a glance: AEC-Q200 automotive power inductor, 68 uH ±20%, 2.2 A Irms, Isat 3 A (20% rolloff @ +25 °C), DCR 190 mOhm, 11.2 x 10.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A1104V3-680-R
    OCL (open circuit inductance)68 uH ±20%
    FLL minimum, at Isat43.5 uH
    Irms (DC, 40 °C rise)2.2 A
    Isat (20% rolloff @ +25 °C)3 A
    DCR typical @ +20 °C190 mOhm
    DCR maximum @ +20 °C210 mOhm
    SRF typical3.1 MHz
    K-factor (Bp-p = K x L x dI)35, Bp-p in Gauss
    Package11.2 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1490

    Mechanical Dimensions & Pad Layout

    HCM1A1104V3-680-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1490: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    Copper loss at the rated current works out to roughly 0.92 W from a typical DCR of 190 mOhm at 2.2 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 306 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 35 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 2,380 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 3.1 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1104V3 line-up this part is number 19 of 19 by inductance, between 0.2 uH and 68 uH.

    Compared with its neighbours in the table, HCM1A1104V3-470-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 11.2 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 210 mOhm becomes roughly 321 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Verify the part marking for revision traceability in production.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products