Eaton HCM1A1105V2-100-R 10 uH Automotive Power Inductor
Eaton HCM1A1105V2-100-R 10 uH Automotive Power Inductor

Eaton HCM1A1105V2-100-R 10 uH Automotive Power Inductor

Share
Eaton HCM1A1105V2-100-R: AEC-Q200 automotive power inductor, 10 uH ±20%, 6.2 A Irms, Isat 7 A, DCR 22 mOhm, 11.2 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1105V2-100-R 10 uH Automotive Power Inductor

    HCM1A1105V2-100-R at a glance: AEC-Q200 automotive power inductor, 10 uH ±20%, 6.2 A Irms, Isat 7 A (20% rolloff @ +25 °C), DCR 22 mOhm, 11.2 x 10.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A1105V2-100-R
    OCL (open circuit inductance)10 uH ±20%
    FLL minimum, at Isat6.4 uH
    Irms (DC, 40 °C rise)6.2 A
    Isat (20% rolloff @ +25 °C)7 A
    DCR typical @ +20 °C22 mOhm
    DCR maximum @ +20 °C27 mOhm
    SRF typical9 MHz
    K-factor (Bp-p = K x L x dI)74, Bp-p in Gauss
    Package11.2 x 10.3 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10909

    Outline Drawing

    HCM1A1105V2-100-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10909: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    Copper loss at the rated current works out to roughly 0.846 W from a typical DCR of 22 mOhm at 6.2 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    At Isat the part holds about 245 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 74 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 740 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 9 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1105V2 family spans 0.68 uH to 68 uH; this row sits at position 13 of 19.

    One step down the table, HCM1A1105V2-6R8-R, sits at 6.8 uH with 7 A and 17.1 mOhm – the lower inductance buys about 2 A of extra current in the same body.

    • Core material: alloy powder core, 11.2 x 10.3 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 27 mOhm becomes roughly 41.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products