
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A1105V2-5R6-R |
| OCL (open circuit inductance) | 5.6 uH ±20% |
| FLL minimum, at Isat | 3.58 uH |
| Irms (DC, 40 °C rise) | 8 A |
| Isat (20% rolloff @ +25 °C) | 12 A |
| DCR typical @ +20 °C | 14 mOhm |
| DCR maximum @ +20 °C | 16.5 mOhm |
| SRF typical | 13 MHz |
| K-factor (Bp-p = K x L x dI) | 98, Bp-p in Gauss |
| Package | 11.2 x 10.3 mm |
| Height | 5.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data 10909 |

Drawing reproduced from Eaton Technical Data 10909: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.
With 14 mOhm typical, the I-squared-R loss at the full 8 A rating is about 0.896 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.
Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.
Stored energy at Isat is about 403 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.
The K-factor of 98 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 549 Gauss of Bp-p, the figure the core-loss curve is plotted against.
Self-resonant frequency is 13 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
Within the HCM1A1105V2 family this is value 11 of 19, in a range that runs from 0.68 uH to 68 uH.
One step down the table, HCM1A1105V2-4R7-R, sits at 4.7 uH with 8.5 A and 11.7 mOhm – the lower inductance buys about 1.5 A of extra current in the same body.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 16.5 mOhm becomes roughly 25.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
Why do V2 and V3 parts exist?
They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd