
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A1105V2-680-R |
| OCL (open circuit inductance) | 68 uH ±20% |
| FLL minimum, at Isat | 43.5 uH |
| Irms (DC, 40 °C rise) | 2.3 A |
| Isat (20% rolloff @ +25 °C) | 4 A |
| DCR typical @ +20 °C | 160 mOhm |
| DCR maximum @ +20 °C | 211 mOhm |
| SRF typical | 3 MHz |
| K-factor (Bp-p = K x L x dI) | 25, Bp-p in Gauss |
| Package | 11.2 x 10.3 mm |
| Height | 5.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data 10909 |

Drawing reproduced from Eaton Technical Data 10909: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.
With 160 mOhm typical, the I-squared-R loss at the full 2.3 A rating is about 0.846 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.
Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.
Energy storage at the saturation current is around 544 uJ, the number that connects the inductance and the current rating into a single transient figure.
K-factor 25 means the flux swing is about 1,700 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.
Self-resonant frequency is 3 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
The HCM1A1105V2 family spans 0.68 uH to 68 uH; this row sits at position 19 of 19.
The next value up in the same family, HCM1A1105V2-470-R, gives 47 uH at 3 A and DCR 97.6 mOhm: the extra inductance costs about 0 A of rated current.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 211 mOhm becomes roughly 323 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
Why do V2 and V3 parts exist?
They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.
Is the part shielded for ADAS modules?
The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.
What is the self-resonant frequency used for?
It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd