Eaton HCM1A1305V2-6R8-R 6.8 uH AEC-Q200 Inductor, 9.5 A
Eaton HCM1A1305V2-6R8-R 6.8 uH AEC-Q200 Inductor, 9.5 A

Eaton HCM1A1305V2-6R8-R 6.8 uH AEC-Q200 Inductor, 9.5 A

Share
Eaton HCM1A1305V2-6R8-R: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 9.5 A Irms, Isat 15 A, DCR 12.1 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1305V2-6R8-R 6.8 uH AEC-Q200 Inductor, 9.5 A

    HCM1A1305V2-6R8-R at a glance: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 9.5 A Irms, Isat 15 A (20% rolloff @ +25 °C), DCR 12.1 mOhm, 13.8 x 12.9 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1305V2-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat4.35 uH
    Irms (DC, 40 °C rise)9.5 A
    Isat (20% rolloff @ +25 °C)15 A
    DCR typical @ +20 °C12.1 mOhm
    DCR maximum @ +20 °C14 mOhm
    SRF typical11 MHz
    K-factor (Bp-p = K x L x dI)82, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10904

    Dimensions and Pad Layout

    HCM1A1305V2-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10904: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    The DCR figure of 12.1 mOhm is what sets the efficiency: at 9.5 A the winding drops about 0.115 mV and dissipates 1.09 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 765 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 82 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 558 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 11 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1305V2 family this is value 16 of 23, in a range that runs from 0.1 uH to 33 uH.

    The next value up in the same family, HCM1A1305V2-7R8-R, gives 7.8 uH at 7.6 A and DCR 15 mOhm: the extra inductance costs about 2.1 A of rated current.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 14 mOhm becomes roughly 21.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Verify the part marking for revision traceability in production.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products