Eaton HCM1A1305V3-1R8-R 1.8 uH Automotive Power Inductor
Eaton HCM1A1305V3-1R8-R 1.8 uH Automotive Power Inductor

Eaton HCM1A1305V3-1R8-R 1.8 uH Automotive Power Inductor

Share
Eaton HCM1A1305V3-1R8-R: AEC-Q200 automotive power inductor, 1.8 uH ±20%, 17 A Irms, Isat 26 A, DCR 3.25 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1305V3-1R8-R 1.8 uH Automotive Power Inductor

    HCM1A1305V3-1R8-R at a glance: AEC-Q200 automotive power inductor, 1.8 uH ±20%, 17 A Irms, Isat 26 A (20% rolloff @ +25 °C), DCR 3.25 mOhm, 13.8 x 12.9 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A1305V3-1R8-R
    OCL (open circuit inductance)1.8 uH ±20%
    FLL minimum, at Isat1.15 uH
    Irms (DC, 40 °C rise)17 A
    Isat (20% rolloff @ +25 °C)26 A
    DCR typical @ +20 °C3.25 mOhm
    DCR maximum @ +20 °C3.74 mOhm
    SRF typical30 MHz
    K-factor (Bp-p = K x L x dI)182, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1488

    Dimensions and Pad Layout

    HCM1A1305V3-1R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1488: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    At the rated 17 A the winding dissipates about 0.939 W in copper alone, using the typical DCR of 3.25 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 608 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 182 means the flux swing is about 328 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 30 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1305V3 line-up this part is number 10 of 23 by inductance, between 0.1 uH and 33 uH.

    One step down the table, HCM1A1305V3-1R5-R, sits at 1.5 uH with 19 A and 2.6 mOhm – the lower inductance buys about 4 A of extra current in the same body.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 3.74 mOhm becomes roughly 5.72 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the qualification file covers the module-level test plan.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products