Eaton HCM1A1307-2R2-R 2.2 uH Shielded Automotive Inductor
Eaton HCM1A1307-2R2-R 2.2 uH Shielded Automotive Inductor

Eaton HCM1A1307-2R2-R 2.2 uH Shielded Automotive Inductor

Share
Eaton HCM1A1307-2R2-R: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 17.6 A Irms, Isat 22 A, DCR 2.96 mOhm, 13.7 x 13 mm.
    • Product Details
    • Download

    Eaton HCM1A1307-2R2-R 2.2 uH Shielded Automotive Inductor

    HCM1A1307-2R2-R at a glance: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 17.6 A Irms, Isat 22 A (20% rolloff @ +25 °C), DCR 2.96 mOhm, 13.7 x 13 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1307-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.4 uH
    Irms (DC, 40 °C rise)17.6 A
    Isat (20% rolloff @ +25 °C)22 A
    DCR typical @ +20 °C2.96 mOhm
    DCR maximum @ +20 °C3.3 mOhm
    K-factor (Bp-p = K x L x dI)97, Bp-p in Gauss
    Package13.7 x 13 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10552

    Outline Drawing

    HCM1A1307-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10552: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    The DCR figure of 2.96 mOhm is what sets the efficiency: at 17.6 A the winding drops about 0.052 mV and dissipates 0.917 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Energy storage at the saturation current is around 532 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 97, a peak-to-peak ripple of one amp produces roughly 213 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1307 line-up this part is number 8 of 20 by inductance, between 0.22 uH and 56 uH.

    The next value up in the same family, HCM1A1307-3R3-R, gives 3.3 uH at 15.6 A and DCR 3.7 mOhm: the extra inductance costs about 3.5 A of rated current.

    • Core material: alloy powder core, 13.7 x 13 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 3.3 mOhm becomes roughly 5.05 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the qualification file covers the module-level test plan.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message