Eaton HCM1A1307-330-R 33 uH AEC-Q200 Inductor, 4.7 A
Eaton HCM1A1307-330-R 33 uH AEC-Q200 Inductor, 4.7 A

Eaton HCM1A1307-330-R 33 uH AEC-Q200 Inductor, 4.7 A

Share
Eaton HCM1A1307-330-R: AEC-Q200 automotive power inductor, 33 uH ±20%, 4.7 A Irms, Isat 6 A, DCR 42 mOhm, 13.7 x 13 mm.
    • Product Details
    • Download

    Eaton HCM1A1307-330-R 33 uH AEC-Q200 Inductor, 4.7 A

    HCM1A1307-330-R at a glance: AEC-Q200 automotive power inductor, 33 uH ±20%, 4.7 A Irms, Isat 6 A (20% rolloff @ +25 °C), DCR 42 mOhm, 13.7 x 13 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1307-330-R
    OCL (open circuit inductance)33 uH ±20%
    FLL minimum, at Isat21 uH
    Irms (DC, 40 °C rise)4.7 A
    Isat (20% rolloff @ +25 °C)6 A
    DCR typical @ +20 °C42 mOhm
    DCR maximum @ +20 °C45 mOhm
    K-factor (Bp-p = K x L x dI)24, Bp-p in Gauss
    Package13.7 x 13 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10552

    Outline Drawing

    HCM1A1307-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10552: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    The DCR figure of 42 mOhm is what sets the efficiency: at 4.7 A the winding drops about 0.197 mV and dissipates 0.928 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 594 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 24 means the flux swing is about 792 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1307 family spans 0.22 uH to 56 uH; this row sits at position 19 of 20.

    Compared with its neighbours in the table, HCM1A1307-560-R trades 0.2 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 13.7 x 13 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 45 mOhm becomes roughly 68.9 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products