Eaton HCM1A1307-5R6-R 5.6 uH AEC-Q200 Inductor, 10 A
Eaton HCM1A1307-5R6-R 5.6 uH AEC-Q200 Inductor, 10 A

Eaton HCM1A1307-5R6-R 5.6 uH AEC-Q200 Inductor, 10 A

Share
Eaton HCM1A1307-5R6-R: AEC-Q200 automotive power inductor, 5.6 uH ±20%, 10 A Irms, Isat 17 A, DCR 7.5 mOhm, 13.7 x 13 mm.
    • Product Details
    • Download

    Eaton HCM1A1307-5R6-R 5.6 uH AEC-Q200 Inductor, 10 A

    HCM1A1307-5R6-R at a glance: AEC-Q200 automotive power inductor, 5.6 uH ±20%, 10 A Irms, Isat 17 A (20% rolloff @ +25 °C), DCR 7.5 mOhm, 13.7 x 13 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1307-5R6-R
    OCL (open circuit inductance)5.6 uH ±20%
    FLL minimum, at Isat3.58 uH
    Irms (DC, 40 °C rise)10 A
    Isat (20% rolloff @ +25 °C)17 A
    DCR typical @ +20 °C7.5 mOhm
    DCR maximum @ +20 °C9 mOhm
    K-factor (Bp-p = K x L x dI)65, Bp-p in Gauss
    Package13.7 x 13 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10552

    Mechanical Dimensions & Pad Layout

    HCM1A1307-5R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10552: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    At the rated 10 A the winding dissipates about 0.75 W in copper alone, using the typical DCR of 7.5 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 809 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 65 means the flux swing is about 364 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1307 family spans 0.22 uH to 56 uH; this row sits at position 11 of 20.

    The next value up in the same family, HCM1A1307-6R8-R, gives 6.8 uH at 9 A and DCR 10 mOhm: the extra inductance costs about 2 A of rated current.

    • Core material: alloy powder core, 13.7 x 13 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 9 mOhm becomes roughly 13.8 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Verify the part marking for revision traceability in production.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products