Eaton HCM1A1307V2-120-R 12 uH Shielded Automotive Inductor
Eaton HCM1A1307V2-120-R 12 uH Shielded Automotive Inductor

Eaton HCM1A1307V2-120-R 12 uH Shielded Automotive Inductor

Share
Eaton HCM1A1307V2-120-R: AEC-Q200 automotive power inductor, 12 uH ±20%, 8 A Irms, Isat 12.5 A, DCR 16.4 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1307V2-120-R 12 uH Shielded Automotive Inductor

    HCM1A1307V2-120-R at a glance: AEC-Q200 automotive power inductor, 12 uH ±20%, 8 A Irms, Isat 12.5 A (20% rolloff @ +25 °C), DCR 16.4 mOhm, 13.8 x 12.9 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A1307V2-120-R
    OCL (open circuit inductance)12 uH ±20%
    FLL minimum, at Isat7.68 uH
    Irms (DC, 40 °C rise)8 A
    Isat (20% rolloff @ +25 °C)12.5 A
    DCR typical @ +20 °C16.4 mOhm
    DCR maximum @ +20 °C18.9 mOhm
    SRF typical6 MHz
    K-factor (Bp-p = K x L x dI)38, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10905

    Mechanical Drawing

    HCM1A1307V2-120-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10905: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    At the rated 8 A the winding dissipates about 1.05 W in copper alone, using the typical DCR of 16.4 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 938 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 38 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 456 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 6 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 20 values listed for HCM1A1307V2, this is the 16th, in a family covering 0.22 uH to 56 uH.

    The next value up in the same family, HCM1A1307V2-150-R, gives 15 uH at 7 A and DCR 20.3 mOhm: the extra inductance costs about 1.3 A of rated current.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 18.9 mOhm becomes roughly 28.9 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Verify the part marking for revision traceability in production.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products