Eaton HCM1A1307V2-1R8-R 1.8 uH AEC-Q200 Inductor, 19 A
Eaton HCM1A1307V2-1R8-R 1.8 uH AEC-Q200 Inductor, 19 A

Eaton HCM1A1307V2-1R8-R 1.8 uH AEC-Q200 Inductor, 19 A

Share
Eaton HCM1A1307V2-1R8-R: AEC-Q200 automotive power inductor, 1.8 uH ±20%, 19 A Irms, Isat 24 A, DCR 2.55 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1307V2-1R8-R 1.8 uH AEC-Q200 Inductor, 19 A

    HCM1A1307V2-1R8-R at a glance: AEC-Q200 automotive power inductor, 1.8 uH ±20%, 19 A Irms, Isat 24 A (20% rolloff @ +25 °C), DCR 2.55 mOhm, 13.8 x 12.9 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1307V2-1R8-R
    OCL (open circuit inductance)1.8 uH ±20%
    FLL minimum, at Isat1.15 uH
    Irms (DC, 40 °C rise)19 A
    Isat (20% rolloff @ +25 °C)24 A
    DCR typical @ +20 °C2.55 mOhm
    DCR maximum @ +20 °C2.94 mOhm
    SRF typical26 MHz
    K-factor (Bp-p = K x L x dI)105, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10905

    Dimensions and Pad Layout

    HCM1A1307V2-1R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10905: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    The DCR figure of 2.55 mOhm is what sets the efficiency: at 19 A the winding drops about 0.048 mV and dissipates 0.921 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 518 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 105 means the flux swing is about 189 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 26 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1307V2 family spans 0.22 uH to 56 uH; this row sits at position 7 of 20.

    The next value up in the same family, HCM1A1307V2-2R2-R, gives 2.2 uH at 18.5 A and DCR 2.62 mOhm: the extra inductance costs about 2.5 A of rated current.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 2.94 mOhm becomes roughly 4.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the qualification and the mounting process match the assembly line.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products