Eaton HCM1A1707-100-R 10 uH AEC-Q200 Inductor, 12 A
Eaton HCM1A1707-100-R 10 uH AEC-Q200 Inductor, 12 A

Eaton HCM1A1707-100-R 10 uH AEC-Q200 Inductor, 12 A

Share
Eaton HCM1A1707-100-R: AEC-Q200 automotive power inductor, 10 uH ±20%, 12 A Irms, Isat 14 A, DCR 9.3 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1A1707-100-R 10 uH AEC-Q200 Inductor, 12 A

    HCM1A1707-100-R at a glance: AEC-Q200 automotive power inductor, 10 uH ±20%, 12 A Irms, Isat 14 A (20% rolloff @ +25 °C), DCR 9.3 mOhm, 17.5 x 17.2 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1707-100-R
    OCL (open circuit inductance)10 uH ±20%
    FLL minimum, at Isat6.4 uH
    Irms (DC, 40 °C rise)12 A
    Isat (20% rolloff @ +25 °C)14 A
    DCR typical @ +20 °C9.3 mOhm
    DCR maximum @ +20 °C10 mOhm
    K-factor (Bp-p = K x L x dI)49, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10553

    Dimensions and Pad Layout

    HCM1A1707-100-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10553: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    The DCR figure of 9.3 mOhm is what sets the efficiency: at 12 A the winding drops about 0.112 mV and dissipates 1.34 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 980 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 49 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 490 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 13 values listed for HCM1A1707, this is the 8th, in a family covering 1 uH to 68 uH.

    One step down the table, HCM1A1707-8R2-R, sits at 8.2 uH with 12 A and 8.1 mOhm – the lower inductance buys about 3 A of extra current in the same body.

    • Core material: alloy powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 10 mOhm becomes roughly 15.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message