
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A1707-330-R |
| OCL (open circuit inductance) | 33 uH ±20% |
| FLL minimum, at Isat | 21.1 uH |
| Irms (DC, 40 °C rise) | 6 A |
| Isat (20% rolloff @ +25 °C) | 9 A |
| DCR typical @ +20 °C | 35.1 mOhm |
| DCR maximum @ +20 °C | 37 mOhm |
| K-factor (Bp-p = K x L x dI) | 20, Bp-p in Gauss |
| Package | 17.5 x 17.2 mm |
| Height | 7.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data 10553 |

Drawing reproduced from Eaton Technical Data 10553: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.
With 35.1 mOhm typical, the I-squared-R loss at the full 6 A rating is about 1.26 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.
Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.
Energy storage at the saturation current is around 1,336 uJ, the number that connects the inductance and the current rating into a single transient figure.
The K-factor of 20 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 660 Gauss of Bp-p, the figure the core-loss curve is plotted against.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
Of the 13 values listed for HCM1A1707, this is the 11th, in a family covering 1 uH to 68 uH.
The next value up in the same family, HCM1A1707-470-R, gives 47 uH at 5.5 A and DCR 41 mOhm: the extra inductance costs about 2.5 A of rated current.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 37 mOhm becomes roughly 56.6 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
What is the self-resonant frequency used for?
It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.
What is the self-resonant frequency used for?
It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.
Why do V2 and V3 parts exist?
They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd