Eaton HCM1A1707-8R2-R 8.2 uH Automotive Power Inductor
Eaton HCM1A1707-8R2-R 8.2 uH Automotive Power Inductor

Eaton HCM1A1707-8R2-R 8.2 uH Automotive Power Inductor

Share
Eaton HCM1A1707-8R2-R: AEC-Q200 automotive power inductor, 8.2 uH ±20%, 12 A Irms, Isat 16 A, DCR 8.1 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1A1707-8R2-R 8.2 uH Automotive Power Inductor

    HCM1A1707-8R2-R at a glance: AEC-Q200 automotive power inductor, 8.2 uH ±20%, 12 A Irms, Isat 16 A (20% rolloff @ +25 °C), DCR 8.1 mOhm, 17.5 x 17.2 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1707-8R2-R
    OCL (open circuit inductance)8.2 uH ±20%
    FLL minimum, at Isat5.25 uH
    Irms (DC, 40 °C rise)12 A
    Isat (20% rolloff @ +25 °C)16 A
    DCR typical @ +20 °C8.1 mOhm
    DCR maximum @ +20 °C8.7 mOhm
    K-factor (Bp-p = K x L x dI)45, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10553

    Mechanical Drawing

    HCM1A1707-8R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10553: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    With 8.1 mOhm typical, the I-squared-R loss at the full 12 A rating is about 1.17 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 1,050 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 45 means the flux swing is about 369 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 13 values listed for HCM1A1707, this is the 7th, in a family covering 1 uH to 68 uH.

    Compared with its neighbours in the table, HCM1A1707-100-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 8.7 mOhm becomes roughly 13.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products