Eaton HCM1A1707V2-1R0-R 1.0 uH AEC-Q200 Inductor, 36 A
Eaton HCM1A1707V2-1R0-R 1.0 uH AEC-Q200 Inductor, 36 A

Eaton HCM1A1707V2-1R0-R 1.0 uH AEC-Q200 Inductor, 36 A

Share
Eaton HCM1A1707V2-1R0-R: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 36 A Irms, Isat 57 A, DCR 1.24 mOhm, 17.45 x 17.15 mm.
    • Product Details
    • Download

    Eaton HCM1A1707V2-1R0-R 1.0 uH AEC-Q200 Inductor, 36 A

    HCM1A1707V2-1R0-R at a glance: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 36 A Irms, Isat 57 A (20% rolloff @ +25 °C), DCR 1.24 mOhm, 17.45 x 17.15 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1707V2-1R0-R
    OCL (open circuit inductance)1.0 uH ±20%
    FLL minimum, at Isat0.64 uH
    Irms (DC, 40 °C rise)36 A
    Isat (20% rolloff @ +25 °C)57 A
    DCR typical @ +20 °C1.24 mOhm
    DCR maximum @ +20 °C1.46 mOhm
    SRF typical34 MHz
    K-factor (Bp-p = K x L x dI)110, Bp-p in Gauss
    Package17.45 x 17.15 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10906

    Mechanical Dimensions & Pad Layout

    HCM1A1707V2-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10906: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    At the rated 36 A the winding dissipates about 1.61 W in copper alone, using the typical DCR of 1.24 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 1,624 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    With K = 110, a peak-to-peak ripple of one amp produces roughly 110 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 34 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1707V2 family this is value 1 of 13, in a range that runs from 1 uH to 68 uH.

    Compared with its neighbours in the table, HCM1A1707V2-1R5-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 17.45 x 17.15 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 1.46 mOhm becomes roughly 2.23 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products