
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A1707V2-470-R |
| OCL (open circuit inductance) | 47 uH ±20% |
| FLL minimum, at Isat | 30.1 uH |
| Irms (DC, 40 °C rise) | 5.5 A |
| Isat (20% rolloff @ +25 °C) | 8 A |
| DCR typical @ +20 °C | 39.9 mOhm |
| DCR maximum @ +20 °C | 46 mOhm |
| SRF typical | 2 MHz |
| K-factor (Bp-p = K x L x dI) | 17, Bp-p in Gauss |
| Package | 17.45 x 17.15 mm |
| Height | 7.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data 10906 |

Drawing reproduced from Eaton Technical Data 10906: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.
At the rated 5.5 A the winding dissipates about 1.21 W in copper alone, using the typical DCR of 39.9 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.
The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.
Stored energy at Isat is about 1,504 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.
The K-factor of 17 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 799 Gauss of Bp-p, the figure the core-loss curve is plotted against.
Self-resonant frequency is 2 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
The HCM1A1707V2 family spans 1 uH to 68 uH; this row sits at position 12 of 13.
One step down the table, HCM1A1707V2-330-R, sits at 33 uH with 6.2 A and 34.8 mOhm – the lower inductance buys about 1.2 A of extra current in the same body.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 46 mOhm becomes roughly 70.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
What is the operating temperature range?
The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd