Eaton HCM1A1707V2-680-R 68 uH AEC-Q200 Inductor, 5 A
Eaton HCM1A1707V2-680-R 68 uH AEC-Q200 Inductor, 5 A

Eaton HCM1A1707V2-680-R 68 uH AEC-Q200 Inductor, 5 A

Share
Eaton HCM1A1707V2-680-R: AEC-Q200 automotive power inductor, 68 uH ±20%, 5 A Irms, Isat 6.8 A, DCR 55.5 mOhm, 17.45 x 17.15 mm.
    • Product Details
    • Download

    Eaton HCM1A1707V2-680-R 68 uH AEC-Q200 Inductor, 5 A

    HCM1A1707V2-680-R at a glance: AEC-Q200 automotive power inductor, 68 uH ±20%, 5 A Irms, Isat 6.8 A (20% rolloff @ +25 °C), DCR 55.5 mOhm, 17.45 x 17.15 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1707V2-680-R
    OCL (open circuit inductance)68 uH ±20%
    FLL minimum, at Isat43.5 uH
    Irms (DC, 40 °C rise)5 A
    Isat (20% rolloff @ +25 °C)6.8 A
    DCR typical @ +20 °C55.5 mOhm
    DCR maximum @ +20 °C60 mOhm
    SRF typical2 MHz
    K-factor (Bp-p = K x L x dI)16, Bp-p in Gauss
    Package17.45 x 17.15 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10906

    Mechanical Dimensions & Pad Layout

    HCM1A1707V2-680-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10906: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    With 55.5 mOhm typical, the I-squared-R loss at the full 5 A rating is about 1.39 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 1,572 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 16 means the flux swing is about 1,088 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 2 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1707V2 family this is value 13 of 13, in a range that runs from 1 uH to 68 uH.

    Compared with its neighbours in the table, HCM1A1707V2-470-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 17.45 x 17.15 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 60 mOhm becomes roughly 91.8 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Verify the qualification and the mounting process match the assembly line.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products