Eaton HCM1A1707V2-8R2-R AEC-Q200 Inductor 8.2 uH, Isat 20 A
Eaton HCM1A1707V2-8R2-R AEC-Q200 Inductor 8.2 uH, Isat 20 A

Eaton HCM1A1707V2-8R2-R AEC-Q200 Inductor 8.2 uH, Isat 20 A

Share
Eaton HCM1A1707V2-8R2-R: AEC-Q200 automotive power inductor, 8.2 uH ±20%, 12.5 A Irms, Isat 20 A, DCR 7.96 mOhm, 17.45 x 17.15 mm.
    • Product Details
    • Download

    Eaton HCM1A1707V2-8R2-R AEC-Q200 Inductor 8.2 uH, Isat 20 A

    HCM1A1707V2-8R2-R at a glance: AEC-Q200 automotive power inductor, 8.2 uH ±20%, 12.5 A Irms, Isat 20 A (20% rolloff @ +25 °C), DCR 7.96 mOhm, 17.45 x 17.15 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1707V2-8R2-R
    OCL (open circuit inductance)8.2 uH ±20%
    FLL minimum, at Isat5.25 uH
    Irms (DC, 40 °C rise)12.5 A
    Isat (20% rolloff @ +25 °C)20 A
    DCR typical @ +20 °C7.96 mOhm
    DCR maximum @ +20 °C8.7 mOhm
    SRF typical8 MHz
    K-factor (Bp-p = K x L x dI)46, Bp-p in Gauss
    Package17.45 x 17.15 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10906

    Dimensions and Pad Layout

    HCM1A1707V2-8R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10906: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    At the rated 12.5 A the winding dissipates about 1.24 W in copper alone, using the typical DCR of 7.96 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 1,640 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 46 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 377 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 8 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1707V2 family spans 1 uH to 68 uH; this row sits at position 7 of 13.

    Compared with its neighbours in the table, HCM1A1707V2-100-R trades 2 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 17.45 x 17.15 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 8.7 mOhm becomes roughly 13.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products