Eaton HCM1A2213V2-2R2-R 2.2 uH AEC-Q200 Inductor, 42.5 A
Eaton HCM1A2213V2-2R2-R 2.2 uH AEC-Q200 Inductor, 42.5 A

Eaton HCM1A2213V2-2R2-R 2.2 uH AEC-Q200 Inductor, 42.5 A

Share
Eaton HCM1A2213V2-2R2-R: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 42.5 A Irms, Isat 48 A, DCR 1.05 mOhm, 22.78 x 22.3 mm.
    • Product Details
    • Download

    Eaton HCM1A2213V2-2R2-R 2.2 uH AEC-Q200 Inductor, 42.5 A

    HCM1A2213V2-2R2-R at a glance: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 42.5 A Irms, Isat 48 A (20% rolloff @ +25 °C), DCR 1.05 mOhm, 22.78 x 22.3 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A2213V2-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.41 uH
    Irms (DC, 40 °C rise)42.5 A
    Isat (20% rolloff @ +25 °C)48 A
    DCR typical @ +20 °C1.05 mOhm
    DCR maximum @ +20 °C1.25 mOhm
    SRF typical17 MHz
    K-factor (Bp-p = K x L x dI)33, Bp-p in Gauss
    Package22.78 x 22.3 mm
    Height13.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10907

    Mechanical Drawing

    HCM1A2213V2-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10907: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    With 1.05 mOhm typical, the I-squared-R loss at the full 42.5 A rating is about 1.9 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 2,534 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 33 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 72.6 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 17 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A2213V2 family this is value 3 of 14, in a range that runs from 0.47 uH to 100 uH.

    The next value up in the same family, HCM1A2213V2-3R3-R, gives 3.3 uH at 34 A and DCR 1.6 mOhm: the extra inductance costs about 16 A of rated current.

    • Core material: alloy powder core, 22.78 x 22.3 mm body at 13.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 1.25 mOhm becomes roughly 1.91 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products