
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A4020V2-4R7-R |
| OCL (open circuit inductance) | 4.7 uH ±20% |
| FLL minimum, at Isat | 2.63 uH |
| Irms (DC, 40 °C rise) | 2.5 A |
| Isat (20% rolloff @ +25 °C) | 3.2 A |
| DCR typical @ +20 °C | 98 mOhm |
| DCR maximum @ +20 °C | 118 mOhm |
| SRF typical | 27 MHz |
| K-factor (Bp-p = K x L x dI) | 587, Bp-p in Gauss |
| Package | 4.75 x 4.45 mm |
| Height | 2.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data 10908 |

Drawing reproduced from Eaton Technical Data 10908: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.
With 98 mOhm typical, the I-squared-R loss at the full 2.5 A rating is about 0.613 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.
Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.
The core stores roughly 24.1 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.
The K-factor of 587 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 2,759 Gauss of Bp-p, the figure the core-loss curve is plotted against.
Self-resonant frequency is 27 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
Of the 15 values listed for HCM1A4020V2, this is the 12th, in a family covering 0.1 uH to 15 uH.
One step down the table, HCM1A4020V2-3R3-R, sits at 3.3 uH with 3.1 A and 71 mOhm – the lower inductance buys about 1.4 A of extra current in the same body.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 118 mOhm becomes roughly 181 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
What is the operating temperature range?
The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.
Is the part shielded for ADAS modules?
The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd