Eaton HCM1A4020V2-R10-R 0.10 uH Automotive Power Inductor
Eaton HCM1A4020V2-R10-R 0.10 uH Automotive Power Inductor

Eaton HCM1A4020V2-R10-R 0.10 uH Automotive Power Inductor

Share
Eaton HCM1A4020V2-R10-R: AEC-Q200 automotive power inductor, 0.10 uH ±20%, 16 A Irms, Isat 22 A, DCR 3.1 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V2-R10-R 0.10 uH Automotive Power Inductor

    HCM1A4020V2-R10-R at a glance: AEC-Q200 automotive power inductor, 0.10 uH ±20%, 16 A Irms, Isat 22 A (20% rolloff @ +25 °C), DCR 3.1 mOhm, 4.75 x 4.45 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A4020V2-R10-R
    OCL (open circuit inductance)0.10 uH ±20%
    FLL minimum, at Isat0.056 uH
    Irms (DC, 40 °C rise)16 A
    Isat (20% rolloff @ +25 °C)22 A
    DCR typical @ +20 °C3.1 mOhm
    DCR maximum @ +20 °C4 mOhm
    SRF typical350 MHz
    K-factor (Bp-p = K x L x dI)2,852, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10908

    Mechanical Drawing

    HCM1A4020V2-R10-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10908: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    At the rated 16 A the winding dissipates about 0.794 W in copper alone, using the typical DCR of 3.1 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 24.2 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 2,852 means the flux swing is about 285 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 350 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A4020V2 line-up this part is number 1 of 15 by inductance, between 0.1 uH and 15 uH.

    One step down the table, HCM1A4020V2-R22-R, sits at 0.22 uH with 11 A and 5.5 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 4 mOhm becomes roughly 6.12 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the part marking for revision traceability in production.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products