Eaton HCM1A4020V2-R33-R 0.33 uH Shielded Automotive Inductor
Eaton HCM1A4020V2-R33-R 0.33 uH Shielded Automotive Inductor

Eaton HCM1A4020V2-R33-R 0.33 uH Shielded Automotive Inductor

Share
Eaton HCM1A4020V2-R33-R: AEC-Q200 automotive power inductor, 0.33 uH ±20%, 8.5 A Irms, Isat 12 A, DCR 7.5 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V2-R33-R 0.33 uH Shielded Automotive Inductor

    HCM1A4020V2-R33-R at a glance: AEC-Q200 automotive power inductor, 0.33 uH ±20%, 8.5 A Irms, Isat 12 A (20% rolloff @ +25 °C), DCR 7.5 mOhm, 4.75 x 4.45 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A4020V2-R33-R
    OCL (open circuit inductance)0.33 uH ±20%
    FLL minimum, at Isat0.185 uH
    Irms (DC, 40 °C rise)8.5 A
    Isat (20% rolloff @ +25 °C)12 A
    DCR typical @ +20 °C7.5 mOhm
    DCR maximum @ +20 °C9 mOhm
    SRF typical140 MHz
    K-factor (Bp-p = K x L x dI)1,906, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10908

    Dimensions and Pad Layout

    HCM1A4020V2-R33-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10908: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    With 7.5 mOhm typical, the I-squared-R loss at the full 8.5 A rating is about 0.542 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 23.8 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 1,906 means the flux swing is about 629 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 140 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A4020V2 family spans 0.1 uH to 15 uH; this row sits at position 3 of 15.

    One step down the table, HCM1A4020V2-R22-R, sits at 0.22 uH with 11 A and 5.5 mOhm – the lower inductance buys about 3.7 A of extra current in the same body.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 9 mOhm becomes roughly 13.8 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the qualification file covers the module-level test plan.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products