
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A4020V2-R47-R |
| OCL (open circuit inductance) | 0.47 uH ±20% |
| FLL minimum, at Isat | 0.263 uH |
| Irms (DC, 40 °C rise) | 7.3 A |
| Isat (20% rolloff @ +25 °C) | 11 A |
| DCR typical @ +20 °C | 10.5 mOhm |
| DCR maximum @ +20 °C | 13 mOhm |
| SRF typical | 120 MHz |
| K-factor (Bp-p = K x L x dI) | 1,744, Bp-p in Gauss |
| Package | 4.75 x 4.45 mm |
| Height | 2.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data 10908 |

Drawing reproduced from Eaton Technical Data 10908: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.
Copper loss at the rated current works out to roughly 0.56 W from a typical DCR of 10.5 mOhm at 7.3 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.
Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.
Stored energy at Isat is about 28.4 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.
The K-factor of 1,744 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 820 Gauss of Bp-p, the figure the core-loss curve is plotted against.
Self-resonant frequency is 120 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
Of the 15 values listed for HCM1A4020V2, this is the 4th, in a family covering 0.1 uH to 15 uH.
Compared with its neighbours in the table, HCM1A4020V2-R56-R trades 1.2 A of rated current for the next inductance step, which is the usual compromise in this family.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 13 mOhm becomes roughly 19.9 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
Why do V2 and V3 parts exist?
They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.
Does the automotive grade change the electrical values?
Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd