Eaton HCM1A4020V3-1R5-R 1.5 uH AEC-Q200 Inductor, 4.5 A
Eaton HCM1A4020V3-1R5-R 1.5 uH AEC-Q200 Inductor, 4.5 A

Eaton HCM1A4020V3-1R5-R 1.5 uH AEC-Q200 Inductor, 4.5 A

Share
Eaton HCM1A4020V3-1R5-R: AEC-Q200 automotive power inductor, 1.5 uH ±20%, 4.5 A Irms, Isat 6 A, DCR 25 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V3-1R5-R 1.5 uH AEC-Q200 Inductor, 4.5 A

    HCM1A4020V3-1R5-R at a glance: AEC-Q200 automotive power inductor, 1.5 uH ±20%, 4.5 A Irms, Isat 6 A (20% rolloff @ +25 °C), DCR 25 mOhm, 4.75 x 4.45 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A4020V3-1R5-R
    OCL (open circuit inductance)1.5 uH ±20%
    FLL minimum, at Isat0.84 uH
    Irms (DC, 40 °C rise)4.5 A
    Isat (20% rolloff @ +25 °C)6 A
    DCR typical @ +20 °C25 mOhm
    DCR maximum @ +20 °C30 mOhm
    SRF typical48 MHz
    K-factor (Bp-p = K x L x dI)1,408, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1495

    Mechanical Dimensions & Pad Layout

    HCM1A4020V3-1R5-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1495: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    The DCR figure of 25 mOhm is what sets the efficiency: at 4.5 A the winding drops about 0.113 mV and dissipates 0.506 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 27 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    With K = 1,408, a peak-to-peak ripple of one amp produces roughly 2,112 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 48 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A4020V3 line-up this part is number 9 of 15 by inductance, between 0.1 uH and 15 uH.

    The next value up in the same family, HCM1A4020V3-2R2-R, gives 2.2 uH at 4.6 A and DCR 40 mOhm: the extra inductance costs about 0.7 A of rated current.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 30 mOhm becomes roughly 45.9 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Confirm the qualification file covers the module-level test plan.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products