Eaton HCM1A4020V3-R22-R 0.22 uH Shielded Automotive Inductor
Eaton HCM1A4020V3-R22-R 0.22 uH Shielded Automotive Inductor

Eaton HCM1A4020V3-R22-R 0.22 uH Shielded Automotive Inductor

Share
Eaton HCM1A4020V3-R22-R: AEC-Q200 automotive power inductor, 0.22 uH ±20%, 11 A Irms, Isat 17 A, DCR 5.5 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V3-R22-R 0.22 uH Shielded Automotive Inductor

    HCM1A4020V3-R22-R at a glance: AEC-Q200 automotive power inductor, 0.22 uH ±20%, 11 A Irms, Isat 17 A (20% rolloff @ +25 °C), DCR 5.5 mOhm, 4.75 x 4.45 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A4020V3-R22-R
    OCL (open circuit inductance)0.22 uH ±20%
    FLL minimum, at Isat0.123 uH
    Irms (DC, 40 °C rise)11 A
    Isat (20% rolloff @ +25 °C)17 A
    DCR typical @ +20 °C5.5 mOhm
    DCR maximum @ +20 °C6.6 mOhm
    SRF typical200 MHz
    K-factor (Bp-p = K x L x dI)1,993, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1495

    Dimensions and Pad Layout

    HCM1A4020V3-R22-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1495: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    The DCR figure of 5.5 mOhm is what sets the efficiency: at 11 A the winding drops about 0.06 mV and dissipates 0.665 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 31.8 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 1,993 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 438 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 200 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A4020V3 line-up this part is number 2 of 15 by inductance, between 0.1 uH and 15 uH.

    Compared with its neighbours in the table, HCM1A4020V3-R33-R trades 7.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 6.6 mOhm becomes roughly 10.1 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products