Eaton HCM1A4020V3-R56-R 0.56 uH AEC-Q200 Inductor, 7.3 A
Eaton HCM1A4020V3-R56-R 0.56 uH AEC-Q200 Inductor, 7.3 A

Eaton HCM1A4020V3-R56-R 0.56 uH AEC-Q200 Inductor, 7.3 A

Share
Eaton HCM1A4020V3-R56-R: AEC-Q200 automotive power inductor, 0.56 uH ±20%, 7.3 A Irms, Isat 10 A, DCR 12 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V3-R56-R 0.56 uH AEC-Q200 Inductor, 7.3 A

    HCM1A4020V3-R56-R at a glance: AEC-Q200 automotive power inductor, 0.56 uH ±20%, 7.3 A Irms, Isat 10 A (20% rolloff @ +25 °C), DCR 12 mOhm, 4.75 x 4.45 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A4020V3-R56-R
    OCL (open circuit inductance)0.56 uH ±20%
    FLL minimum, at Isat0.314 uH
    Irms (DC, 40 °C rise)7.3 A
    Isat (20% rolloff @ +25 °C)10 A
    DCR typical @ +20 °C12 mOhm
    DCR maximum @ +20 °C15 mOhm
    SRF typical95 MHz
    K-factor (Bp-p = K x L x dI)2,007, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1495

    Mechanical Dimensions & Pad Layout

    HCM1A4020V3-R56-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1495: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 0.639 W from a typical DCR of 12 mOhm at 7.3 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 28 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 2,007 means the flux swing is about 1,124 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 95 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A4020V3 family spans 0.1 uH to 15 uH; this row sits at position 5 of 15.

    One step down the table, HCM1A4020V3-R47-R, sits at 0.47 uH with 7.3 A and 10.5 mOhm – the lower inductance buys about 0.6 A of extra current in the same body.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 15 mOhm becomes roughly 23 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products