Eaton HCMA0503-100-R 10 uH Molded Automotive Inductor
Eaton HCMA0503-100-R 10 uH Molded Automotive Inductor

Eaton HCMA0503-100-R 10 uH Molded Automotive Inductor

Share
Eaton HCMA0503-100-R: AEC-Q200 high-current inductor, 10 uH ±20%, 2.75 A Irms, Isat 2.3 A, DCR 122 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCMA0503-100-R 10 uH Molded Automotive Inductor

    HCMA0503-100-R at a glance: AEC-Q200 high-current inductor, 10 uH ±20%, 2.75 A Irms, Isat 2.3 A (20% rolloff @ +25 °C), DCR 122 mOhm, 5.5 x 5.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA0503-100-R
    OCL (open circuit inductance)10 uH ±20%
    FLL minimum, at Isat6.4 uH
    Irms (DC, 40 °C rise)2.75 A
    Isat (20% rolloff @ +25 °C)2.3 A
    DCR typical @ +20 °C122 mOhm
    DCR maximum @ +20 °C132 mOhm
    K-factor (Bp-p = K x L x dI)158, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10248

    Mechanical Dimensions & Pad Layout

    HCMA0503-100-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10248: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    With 122 mOhm typical, the I-squared-R loss at the full 2.75 A rating is about 0.923 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 26.4 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    With K = 158, a peak-to-peak ripple of one amp produces roughly 1,580 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    In the HCMA0503 line-up this part is number 12 of 14 by inductance, between 0.2 uH and 22 uH.

    One step down the table, HCMA0503-6R8-R, sits at 6.8 uH with 2.6 A and 91 mOhm – the lower inductance buys about 0.2 A of extra current in the same body.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning con­ trollers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 132 mOhm becomes roughly 186 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Verify the shielding against the EMC plan for the board.
    • Size the saturation margin at the maximum ambient the module will see.

    Frequently Asked Questions

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products