Eaton HCMA0503-220-R 22 uH Automotive High-Current Inductor
Eaton HCMA0503-220-R 22 uH Automotive High-Current Inductor

Eaton HCMA0503-220-R 22 uH Automotive High-Current Inductor

Share
Eaton HCMA0503-220-R: AEC-Q200 high-current inductor, 22 uH ±20%, 1.9 A Irms, Isat 1.9 A, DCR 260 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCMA0503-220-R 22 uH Automotive High-Current Inductor

    HCMA0503-220-R at a glance: AEC-Q200 high-current inductor, 22 uH ±20%, 1.9 A Irms, Isat 1.9 A (20% rolloff @ +25 °C), DCR 260 mOhm, 5.5 x 5.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA0503-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat14 uH
    Irms (DC, 40 °C rise)1.9 A
    Isat (20% rolloff @ +25 °C)1.9 A
    DCR typical @ +20 °C260 mOhm
    DCR maximum @ +20 °C270 mOhm
    K-factor (Bp-p = K x L x dI)106, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10248

    Outline Drawing

    HCMA0503-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10248: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    The DCR figure of 260 mOhm is what sets the efficiency: at 1.9 A the winding drops about 0.494 mV and dissipates 0.939 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    At Isat the part holds about 39.7 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 106, a peak-to-peak ripple of one amp produces roughly 2,332 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA0503 family spans 0.2 uH to 22 uH; this row sits at position 14 of 14.

    One step down the table, HCMA0503-150-R, sits at 15 uH with 2.4 A and 138 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning con­ trollers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 270 mOhm becomes roughly 381 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Confirm the terminal spacing against the rail voltage.
    • Compare against the commercial HCM row of the same size before substituting.
    • Size the saturation margin at the maximum ambient the module will see.

    Frequently Asked Questions

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    What is the difference between Irms and Isat here?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products