Eaton HCMA0503-5R6-R 5.6 uH Automotive High-Current Inductor
Eaton HCMA0503-5R6-R 5.6 uH Automotive High-Current Inductor

Eaton HCMA0503-5R6-R 5.6 uH Automotive High-Current Inductor

Share
Eaton HCMA0503-5R6-R: AEC-Q200 high-current inductor, 5.6 uH ±20%, 4.25 A Irms, Isat 3.5 A, DCR 63 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCMA0503-5R6-R 5.6 uH Automotive High-Current Inductor

    HCMA0503-5R6-R at a glance: AEC-Q200 high-current inductor, 5.6 uH ±20%, 4.25 A Irms, Isat 3.5 A (20% rolloff @ +25 °C), DCR 63 mOhm, 5.5 x 5.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA0503-5R6-R
    OCL (open circuit inductance)5.6 uH ±20%
    FLL minimum, at Isat3.6 uH
    Irms (DC, 40 °C rise)4.25 A
    Isat (20% rolloff @ +25 °C)3.5 A
    DCR typical @ +20 °C63 mOhm
    DCR maximum @ +20 °C70.6 mOhm
    K-factor (Bp-p = K x L x dI)206, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10248

    Mechanical Dimensions & Pad Layout

    HCMA0503-5R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10248: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    The family takes the molded construction used on the commercial high-current parts and applies the automotive qualification and temperature range. Soft saturation and low DCR are the two properties that matter on a 48 V or 12 V rail carrying tens of amps.

    Copper loss at the rated current works out to roughly 1.14 W from a typical DCR of 63 mOhm at 4.25 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 34.3 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 206, a peak-to-peak ripple of one amp produces roughly 1,154 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA0503 family spans 0.2 uH to 22 uH; this row sits at position 10 of 14.

    Compared with its neighbours in the table, HCMA0503-6R8-R trades 1.9 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning con­ trollers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 70.6 mOhm becomes roughly 99.7 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Confirm the terminal spacing against the rail voltage.
    • Confirm the terminal spacing against the rail voltage.
    • Verify the shielding against the EMC plan for the board.

    Frequently Asked Questions

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message