Eaton HCMA0703-1R0-R 1.0 uH AEC-Q200 Inductor, 11 A
Eaton HCMA0703-1R0-R 1.0 uH AEC-Q200 Inductor, 11 A

Eaton HCMA0703-1R0-R 1.0 uH AEC-Q200 Inductor, 11 A

Share
Eaton HCMA0703-1R0-R: AEC-Q200 high-current inductor, 1.0 uH ±20%, 11 A Irms, Isat 22 A, DCR 9 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCMA0703-1R0-R 1.0 uH AEC-Q200 Inductor, 11 A

    HCMA0703-1R0-R at a glance: AEC-Q200 high-current inductor, 1.0 uH ±20%, 11 A Irms, Isat 22 A (20% rolloff @ +25 °C), DCR 9 mOhm, 7.4 x 7 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCMA0703-1R0-R
    OCL (open circuit inductance)1.0 uH ±20%
    FLL minimum, at Isat0.6 uH
    Irms (DC, 40 °C rise)11 A
    Isat (20% rolloff @ +25 °C)22 A
    DCR typical @ +20 °C9 mOhm
    DCR maximum @ +20 °C10 mOhm
    K-factor (Bp-p = K x L x dI)374, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10282

    Outline Drawing

    HCMA0703-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10282: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified high-current inductor on a molded powder core, rated to +125 °C. The construction is chosen for current density: the winding is pressed into the magnetic material, so there is no bobbin wasting window area and the DCR stays low for the body size.

    Copper loss at the rated current works out to roughly 1.09 W from a typical DCR of 9 mOhm at 11 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 242 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 374 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 374 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Within the HCMA0703 family this is value 6 of 15, in a range that runs from 0.15 uH to 33 uH.

    The next value up in the same family, HCMA0703-1R5-R, gives 1.5 uH at 9 A and DCR 14 mOhm: the extra inductance costs about 4 A of rated current.

    • Core material: iron powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 10 mOhm becomes roughly 14.1 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Verify the shielding against the EMC plan for the board.
    • Compare against the commercial HCM row of the same size before substituting.
    • Verify the shielding against the EMC plan for the board.

    Frequently Asked Questions

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products