Eaton HCMA0703-1R5-R 1.5 uH Molded Automotive Inductor
Eaton HCMA0703-1R5-R 1.5 uH Molded Automotive Inductor

Eaton HCMA0703-1R5-R 1.5 uH Molded Automotive Inductor

Share
Eaton HCMA0703-1R5-R: AEC-Q200 high-current inductor, 1.5 uH ±20%, 9 A Irms, Isat 18 A, DCR 14 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCMA0703-1R5-R 1.5 uH Molded Automotive Inductor

    HCMA0703-1R5-R at a glance: AEC-Q200 high-current inductor, 1.5 uH ±20%, 9 A Irms, Isat 18 A (20% rolloff @ +25 °C), DCR 14 mOhm, 7.4 x 7 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCMA0703-1R5-R
    OCL (open circuit inductance)1.5 uH ±20%
    FLL minimum, at Isat0.9 uH
    Irms (DC, 40 °C rise)9 A
    Isat (20% rolloff @ +25 °C)18 A
    DCR typical @ +20 °C14 mOhm
    DCR maximum @ +20 °C15 mOhm
    K-factor (Bp-p = K x L x dI)366, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10282

    Dimensions and Pad Layout

    HCMA0703-1R5-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10282: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    The family takes the molded construction used on the commercial high-current parts and applies the automotive qualification and temperature range. Soft saturation and low DCR are the two properties that matter on a 48 V or 12 V rail carrying tens of amps.

    The DCR figure of 14 mOhm is what sets the efficiency: at 9 A the winding drops about 0.126 mV and dissipates 1.13 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 243 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 366 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 549 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Positioning in the Range

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA0703 family spans 0.15 uH to 33 uH; this row sits at position 7 of 15.

    One step down the table, HCMA0703-1R0-R, sits at 1.0 uH with 11 A and 9 mOhm – the lower inductance buys about 3 A of extra current in the same body.

    • Core material: iron powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 15 mOhm becomes roughly 21.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the current derating at the maximum ambient of the module.
    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Verify the shielding against the EMC plan for the board.

    Frequently Asked Questions

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    What is the difference between Irms and Isat here?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products