Eaton HCMA0703-6R8-R 6.8 uH Molded Automotive Inductor
Eaton HCMA0703-6R8-R 6.8 uH Molded Automotive Inductor

Eaton HCMA0703-6R8-R 6.8 uH Molded Automotive Inductor

Share
Eaton HCMA0703-6R8-R: AEC-Q200 high-current inductor, 6.8 uH ±20%, 4.5 A Irms, Isat 8 A, DCR 54 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCMA0703-6R8-R 6.8 uH Molded Automotive Inductor

    HCMA0703-6R8-R at a glance: AEC-Q200 high-current inductor, 6.8 uH ±20%, 4.5 A Irms, Isat 8 A (20% rolloff @ +25 °C), DCR 54 mOhm, 7.4 x 7 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCMA0703-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat4.08 uH
    Irms (DC, 40 °C rise)4.5 A
    Isat (20% rolloff @ +25 °C)8 A
    DCR typical @ +20 °C54 mOhm
    DCR maximum @ +20 °C60 mOhm
    K-factor (Bp-p = K x L x dI)151, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10282

    Mechanical Dimensions & Pad Layout

    HCMA0703-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10282: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    The family takes the molded construction used on the commercial high-current parts and applies the automotive qualification and temperature range. Soft saturation and low DCR are the two properties that matter on a 48 V or 12 V rail carrying tens of amps.

    The DCR figure of 54 mOhm is what sets the efficiency: at 4.5 A the winding drops about 0.243 mV and dissipates 1.09 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 218 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 151 means the flux swing is about 1,027 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Series Positioning

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA0703 family spans 0.15 uH to 33 uH; this row sits at position 11 of 15.

    One step down the table, HCMA0703-4R7-R, sits at 4.7 uH with 5.5 A and 37 mOhm – the lower inductance buys about 1.5 A of extra current in the same body.

    • Core material: iron powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 60 mOhm becomes roughly 84.8 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the current derating at the maximum ambient of the module.
    • Verify the shielding against the EMC plan for the board.
    • Size the saturation margin at the maximum ambient the module will see.

    Frequently Asked Questions

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    What is the difference between Irms and Isat here?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message