Eaton HCMA0703-R22-R 0.22 uH AEC-Q200 Inductor, 23 A
Eaton HCMA0703-R22-R 0.22 uH AEC-Q200 Inductor, 23 A

Eaton HCMA0703-R22-R 0.22 uH AEC-Q200 Inductor, 23 A

Share
Eaton HCMA0703-R22-R: AEC-Q200 high-current inductor, 0.22 uH ±20%, 23 A Irms, Isat 40 A, DCR 2.5 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCMA0703-R22-R 0.22 uH AEC-Q200 Inductor, 23 A

    HCMA0703-R22-R at a glance: AEC-Q200 high-current inductor, 0.22 uH ±20%, 23 A Irms, Isat 40 A (20% rolloff @ +25 °C), DCR 2.5 mOhm, 7.4 x 7 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA0703-R22-R
    OCL (open circuit inductance)0.22 uH ±20%
    FLL minimum, at Isat0.13 uH
    Irms (DC, 40 °C rise)23 A
    Isat (20% rolloff @ +25 °C)40 A
    DCR typical @ +20 °C2.5 mOhm
    DCR maximum @ +20 °C2.8 mOhm
    K-factor (Bp-p = K x L x dI)986, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10282

    Outline Drawing

    HCMA0703-R22-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10282: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    Copper loss at the rated current works out to roughly 1.32 W from a typical DCR of 2.5 mOhm at 23 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Energy storage at the saturation current is around 176 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 986 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 217 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA0703 family spans 0.15 uH to 33 uH; this row sits at position 2 of 15.

    The next value up in the same family, HCMA0703-R47-R, gives 0.47 uH at 17.5 A and DCR 4 mOhm: the extra inductance costs about 8.5 A of rated current.

    • Core material: iron powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 2.8 mOhm becomes roughly 3.96 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Compare against the commercial HCM row of the same size before substituting.
    • Verify the shielding against the EMC plan for the board.
    • Check the terminal spacing against the rail voltage and the coating scheme.

    Frequently Asked Questions

    What is the difference between Irms and Isat here?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products