Eaton HCMA1104-R20-R 0.20 uH Automotive High-Current Inductor
Eaton HCMA1104-R20-R 0.20 uH Automotive High-Current Inductor

Eaton HCMA1104-R20-R 0.20 uH Automotive High-Current Inductor

Share
Eaton HCMA1104-R20-R: AEC-Q200 high-current inductor, 0.20 uH ±20%, 32 A Irms, Isat 45 A, DCR 0.63 mOhm, 11.5 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCMA1104-R20-R 0.20 uH Automotive High-Current Inductor

    HCMA1104-R20-R at a glance: AEC-Q200 high-current inductor, 0.20 uH ±20%, 32 A Irms, Isat 45 A (20% rolloff @ +25 °C), DCR 0.63 mOhm, 11.5 x 10.3 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCMA1104-R20-R
    OCL (open circuit inductance)0.20 uH ±20%
    FLL minimum, at Isat0.13 uH
    Irms (DC, 40 °C rise)32 A
    Isat (20% rolloff @ +25 °C)45 A
    DCR typical @ +20 °C0.63 mOhm
    DCR maximum @ +20 °C0.72 mOhm
    K-factor (Bp-p = K x L x dI)411, Bp-p in Gauss
    Package11.5 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10349

    Mechanical Drawing

    HCMA1104-R20-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10349: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    At the rated 32 A the winding dissipates about 0.645 W in copper alone, using the typical DCR of 0.63 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 202 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 411, a peak-to-peak ripple of one amp produces roughly 82.2 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    What This Family Is For

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Within the HCMA1104 family this is value 1 of 12, in a range that runs from 0.2 uH to 22 uH.

    The next value up in the same family, HCMA1104-R36-R, gives 0.36 uH at 30 A and DCR 1.04 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: iron powder core, 11.5 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning con- trollers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 0.72 mOhm becomes roughly 1.02 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Size the saturation margin at the maximum ambient the module will see.
    • Size the saturation margin at the maximum ambient the module will see.
    • Check the terminal spacing against the rail voltage and the coating scheme.

    Frequently Asked Questions

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products