Eaton HCMA1104-R45-R 0.45 uH Molded Automotive Inductor
Eaton HCMA1104-R45-R 0.45 uH Molded Automotive Inductor

Eaton HCMA1104-R45-R 0.45 uH Molded Automotive Inductor

Share
Eaton HCMA1104-R45-R: AEC-Q200 high-current inductor, 0.45 uH ±20%, 29 A Irms, Isat 36 A, DCR 1.07 mOhm, 11.5 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCMA1104-R45-R 0.45 uH Molded Automotive Inductor

    HCMA1104-R45-R at a glance: AEC-Q200 high-current inductor, 0.45 uH ±20%, 29 A Irms, Isat 36 A (20% rolloff @ +25 °C), DCR 1.07 mOhm, 11.5 x 10.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA1104-R45-R
    OCL (open circuit inductance)0.45 uH ±20%
    FLL minimum, at Isat0.29 uH
    Irms (DC, 40 °C rise)29 A
    Isat (20% rolloff @ +25 °C)36 A
    DCR typical @ +20 °C1.07 mOhm
    DCR maximum @ +20 °C1.23 mOhm
    K-factor (Bp-p = K x L x dI)219, Bp-p in Gauss
    Package11.5 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10349

    Dimensions and Pad Layout

    HCMA1104-R45-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10349: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified high-current inductor on a molded powder core, rated to +125 °C. The construction is chosen for current density: the winding is pressed into the magnetic material, so there is no bobbin wasting window area and the DCR stays low for the body size.

    At the rated 29 A the winding dissipates about 0.9 W in copper alone, using the typical DCR of 1.07 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    At Isat the part holds about 292 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 219, a peak-to-peak ripple of one amp produces roughly 98.5 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    What This Family Is For

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA1104 family spans 0.2 uH to 22 uH; this row sits at position 3 of 12.

    Compared with its neighbours in the table, HCMA1104-R56-R trades 5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 11.5 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning con- trollers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 1.23 mOhm becomes roughly 1.74 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Compare against the commercial HCM row of the same size before substituting.
    • Verify the shielding against the EMC plan for the board.
    • Compare against the commercial HCM row of the same size before substituting.

    Frequently Asked Questions

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products