Eaton HCMA1305-100-R 10.0 uH Automotive High-Current Inductor
Eaton HCMA1305-100-R 10.0 uH Automotive High-Current Inductor

Eaton HCMA1305-100-R 10.0 uH Automotive High-Current Inductor

Share
Eaton HCMA1305-100-R: AEC-Q200 high-current inductor, 10.0 uH ±20%, 9 A Irms, Isat 16 A, DCR 19 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-100-R 10.0 uH Automotive High-Current Inductor

    HCMA1305-100-R at a glance: AEC-Q200 high-current inductor, 10.0 uH ±20%, 9 A Irms, Isat 16 A (20% rolloff @ +25 °C), DCR 19 mOhm, 13.8 x 12.5 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCMA1305-100-R
    OCL (open circuit inductance)10.0 uH ±20%
    FLL minimum, at Isat6.4 uH
    Irms (DC, 40 °C rise)9 A
    Isat (20% rolloff @ +25 °C)16 A
    DCR typical @ +20 °C19 mOhm
    DCR maximum @ +20 °C21.9 mOhm
    K-factor (Bp-p = K x L x dI)90, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Dimensions & Pad Layout

    HCMA1305-100-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    With 19 mOhm typical, the I-squared-R loss at the full 9 A rating is about 1.54 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 1,280 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 90 means the flux swing is about 900 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Series Positioning

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Within the HCMA1305 family this is value 18 of 21, in a range that runs from 0.1 uH to 33 uH.

    The next value up in the same family, HCMA1305-150-R, gives 15.0 uH at 7.7 A and DCR 29 mOhm: the extra inductance costs about 1.8 A of rated current.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 21.9 mOhm becomes roughly 30.9 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Verify the shielding against the EMC plan for the board.
    • Size the saturation margin at the maximum ambient the module will see.
    • Check the current derating at the maximum ambient of the module.

    Frequently Asked Questions

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products