Eaton HCMA1305-150-R 15.0 uH AEC-Q200 Inductor, 7.7 A
Eaton HCMA1305-150-R 15.0 uH AEC-Q200 Inductor, 7.7 A

Eaton HCMA1305-150-R 15.0 uH AEC-Q200 Inductor, 7.7 A

Share
Eaton HCMA1305-150-R: AEC-Q200 high-current inductor, 15.0 uH ±20%, 7.7 A Irms, Isat 13 A, DCR 29 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-150-R 15.0 uH AEC-Q200 Inductor, 7.7 A

    HCMA1305-150-R at a glance: AEC-Q200 high-current inductor, 15.0 uH ±20%, 7.7 A Irms, Isat 13 A (20% rolloff @ +25 °C), DCR 29 mOhm, 13.8 x 12.5 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA1305-150-R
    OCL (open circuit inductance)15.0 uH ±20%
    FLL minimum, at Isat9.6 uH
    Irms (DC, 40 °C rise)7.7 A
    Isat (20% rolloff @ +25 °C)13 A
    DCR typical @ +20 °C29 mOhm
    DCR maximum @ +20 °C33.4 mOhm
    K-factor (Bp-p = K x L x dI)74, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Drawing

    HCMA1305-150-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the high-current member of the automotive molded family. Where the standard automotive parts top out at a few tens of amps, this one is built for the main DC-DC stage: thicker winding, larger body, and a saturation current that scales with it.

    The DCR figure of 29 mOhm is what sets the efficiency: at 7.7 A the winding drops about 0.223 mV and dissipates 1.72 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 1,268 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 74 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,110 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Positioning in the Range

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Within the HCMA1305 family this is value 19 of 21, in a range that runs from 0.1 uH to 33 uH.

    The next value up in the same family, HCMA1305-220-R, gives 22.0 uH at 6.2 A and DCR 45 mOhm: the extra inductance costs about 2.8 A of rated current.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 33.4 mOhm becomes roughly 47.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Compare against the commercial HCM row of the same size before substituting.
    • Check the terminal spacing against the rail voltage and the coating scheme.

    Frequently Asked Questions

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products