Eaton HCMA1305-2R2-R 2.20 uH AEC-Q200 Inductor, 20 A
Eaton HCMA1305-2R2-R 2.20 uH AEC-Q200 Inductor, 20 A

Eaton HCMA1305-2R2-R 2.20 uH AEC-Q200 Inductor, 20 A

Share
Eaton HCMA1305-2R2-R: AEC-Q200 high-current inductor, 2.20 uH ±20%, 20 A Irms, Isat 32 A, DCR 4.6 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-2R2-R 2.20 uH AEC-Q200 Inductor, 20 A

    HCMA1305-2R2-R at a glance: AEC-Q200 high-current inductor, 2.20 uH ±20%, 20 A Irms, Isat 32 A (20% rolloff @ +25 °C), DCR 4.6 mOhm, 13.8 x 12.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA1305-2R2-R
    OCL (open circuit inductance)2.20 uH ±20%
    FLL minimum, at Isat1.41 uH
    Irms (DC, 40 °C rise)20 A
    Isat (20% rolloff @ +25 °C)32 A
    DCR typical @ +20 °C4.6 mOhm
    DCR maximum @ +20 °C5.29 mOhm
    K-factor (Bp-p = K x L x dI)191, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Dimensions & Pad Layout

    HCMA1305-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified high-current inductor on a molded powder core, rated to +125 °C. The construction is chosen for current density: the winding is pressed into the magnetic material, so there is no bobbin wasting window area and the DCR stays low for the body size.

    Copper loss at the rated current works out to roughly 1.84 W from a typical DCR of 4.6 mOhm at 20 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 1,126 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    With K = 191, a peak-to-peak ripple of one amp produces roughly 420 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Of the 21 values listed for HCMA1305, this is the 11th, in a family covering 0.1 uH to 33 uH.

    Compared with its neighbours in the table, HCMA1305-3R3-R trades 6 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 5.29 mOhm becomes roughly 7.47 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Size the saturation margin at the maximum ambient the module will see.
    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Confirm the terminal spacing against the rail voltage.

    Frequently Asked Questions

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products