Eaton HCMA1305-3R3-R 3.30 uH Molded Automotive Inductor
Eaton HCMA1305-3R3-R 3.30 uH Molded Automotive Inductor

Eaton HCMA1305-3R3-R 3.30 uH Molded Automotive Inductor

Share
Eaton HCMA1305-3R3-R: AEC-Q200 high-current inductor, 3.30 uH ±20%, 15 A Irms, Isat 32 A, DCR 7.7 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-3R3-R 3.30 uH Molded Automotive Inductor

    HCMA1305-3R3-R at a glance: AEC-Q200 high-current inductor, 3.30 uH ±20%, 15 A Irms, Isat 32 A (20% rolloff @ +25 °C), DCR 7.7 mOhm, 13.8 x 12.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA1305-3R3-R
    OCL (open circuit inductance)3.30 uH ±20%
    FLL minimum, at Isat2.11 uH
    Irms (DC, 40 °C rise)15 A
    Isat (20% rolloff @ +25 °C)32 A
    DCR typical @ +20 °C7.7 mOhm
    DCR maximum @ +20 °C9.2 mOhm
    K-factor (Bp-p = K x L x dI)170, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Drawing

    HCMA1305-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    The family takes the molded construction used on the commercial high-current parts and applies the automotive qualification and temperature range. Soft saturation and low DCR are the two properties that matter on a 48 V or 12 V rail carrying tens of amps.

    With 7.7 mOhm typical, the I-squared-R loss at the full 15 A rating is about 1.73 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 1,690 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 170 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 561 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Series Positioning

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Of the 21 values listed for HCMA1305, this is the 12th, in a family covering 0.1 uH to 33 uH.

    Compared with its neighbours in the table, HCMA1305-4R7-R trades 8 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 9.2 mOhm becomes roughly 13 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Verify the shielding against the EMC plan for the board.
    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Compare against the commercial HCM row of the same size before substituting.

    Frequently Asked Questions

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message