Eaton HCMA1305-8R2-R AEC-Q200 Inductor 8.20 uH, Isat 18 A
Eaton HCMA1305-8R2-R AEC-Q200 Inductor 8.20 uH, Isat 18 A

Eaton HCMA1305-8R2-R AEC-Q200 Inductor 8.20 uH, Isat 18 A

Share
Eaton HCMA1305-8R2-R: AEC-Q200 high-current inductor, 8.20 uH ±20%, 9.5 A Irms, Isat 18 A, DCR 17.5 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-8R2-R AEC-Q200 Inductor 8.20 uH, Isat 18 A

    HCMA1305-8R2-R at a glance: AEC-Q200 high-current inductor, 8.20 uH ±20%, 9.5 A Irms, Isat 18 A (20% rolloff @ +25 °C), DCR 17.5 mOhm, 13.8 x 12.5 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA1305-8R2-R
    OCL (open circuit inductance)8.20 uH ±20%
    FLL minimum, at Isat5.25 uH
    Irms (DC, 40 °C rise)9.5 A
    Isat (20% rolloff @ +25 °C)18 A
    DCR typical @ +20 °C17.5 mOhm
    DCR maximum @ +20 °C20.1 mOhm
    K-factor (Bp-p = K x L x dI)117, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Outline Drawing

    HCMA1305-8R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the high-current member of the automotive molded family. Where the standard automotive parts top out at a few tens of amps, this one is built for the main DC-DC stage: thicker winding, larger body, and a saturation current that scales with it.

    At the rated 9.5 A the winding dissipates about 1.58 W in copper alone, using the typical DCR of 17.5 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 1,328 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 117 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 959 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Of the 21 values listed for HCMA1305, this is the 17th, in a family covering 0.1 uH to 33 uH.

    The next value up in the same family, HCMA1305-100-R, gives 10.0 uH at 9 A and DCR 19 mOhm: the extra inductance costs about 1 A of rated current.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 20.1 mOhm becomes roughly 28.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the current derating at the maximum ambient of the module.
    • Confirm the terminal spacing against the rail voltage.
    • Size the saturation margin at the maximum ambient the module will see.

    Frequently Asked Questions

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products