Eaton HCMA1305-R68-R 0.68 uH Automotive High-Current Inductor
Eaton HCMA1305-R68-R 0.68 uH Automotive High-Current Inductor

Eaton HCMA1305-R68-R 0.68 uH Automotive High-Current Inductor

Share
Eaton HCMA1305-R68-R: AEC-Q200 high-current inductor, 0.68 uH ±20%, 34 A Irms, Isat 54 A, DCR 1.15 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-R68-R 0.68 uH Automotive High-Current Inductor

    HCMA1305-R68-R at a glance: AEC-Q200 high-current inductor, 0.68 uH ±20%, 34 A Irms, Isat 54 A (20% rolloff @ +25 °C), DCR 1.15 mOhm, 13.8 x 12.5 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA1305-R68-R
    OCL (open circuit inductance)0.68 uH ±20%
    FLL minimum, at Isat0.44 uH
    Irms (DC, 40 °C rise)34 A
    Isat (20% rolloff @ +25 °C)54 A
    DCR typical @ +20 °C1.15 mOhm
    DCR maximum @ +20 °C1.33 mOhm
    K-factor (Bp-p = K x L x dI)500, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Outline Drawing

    HCMA1305-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the high-current member of the automotive molded family. Where the standard automotive parts top out at a few tens of amps, this one is built for the main DC-DC stage: thicker winding, larger body, and a saturation current that scales with it.

    The DCR figure of 1.15 mOhm is what sets the efficiency: at 34 A the winding drops about 0.039 mV and dissipates 1.33 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 991 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 500 means the flux swing is about 340 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Positioning in the Range

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    In the HCMA1305 line-up this part is number 6 of 21 by inductance, between 0.1 uH and 33 uH.

    One step down the table, HCMA1305-R56-R, sits at 0.56 uH with 36 A and 1.15 mOhm – the lower inductance buys about 5 A of extra current in the same body.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 1.33 mOhm becomes roughly 1.88 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the current derating at the maximum ambient of the module.
    • Verify the shielding against the EMC plan for the board.
    • Compare against the commercial HCM row of the same size before substituting.

    Frequently Asked Questions

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    What is the difference between Irms and Isat here?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products