Eaton HCMA1707-100-R 10 uH AEC-Q200 Inductor, 14 A
Eaton HCMA1707-100-R 10 uH AEC-Q200 Inductor, 14 A

Eaton HCMA1707-100-R 10 uH AEC-Q200 Inductor, 14 A

Share
Eaton HCMA1707-100-R: AEC-Q200 high-current inductor, 10 uH ±20%, 14 A Irms, Isat 18 A, DCR 9.3 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCMA1707-100-R 10 uH AEC-Q200 Inductor, 14 A

    HCMA1707-100-R at a glance: AEC-Q200 high-current inductor, 10 uH ±20%, 14 A Irms, Isat 18 A (20% rolloff @ +25 °C), DCR 9.3 mOhm, 17.5 x 17.2 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCMA1707-100-R
    OCL (open circuit inductance)10 uH ±20%
    FLL minimum, at Isat6.4 uH
    Irms (DC, 40 °C rise)14 A
    Isat (20% rolloff @ +25 °C)18 A
    DCR typical @ +20 °C9.3 mOhm
    DCR maximum @ +20 °C10 mOhm
    K-factor (Bp-p = K x L x dI)47, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10296

    Mechanical Dimensions & Pad Layout

    HCMA1707-100-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10296: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    The family takes the molded construction used on the commercial high-current parts and applies the automotive qualification and temperature range. Soft saturation and low DCR are the two properties that matter on a 48 V or 12 V rail carrying tens of amps.

    The DCR figure of 9.3 mOhm is what sets the efficiency: at 14 A the winding drops about 0.13 mV and dissipates 1.82 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 1,620 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 47 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 470 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Series Positioning

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    In the HCMA1707 line-up this part is number 6 of 11 by inductance, between 1.5 uH and 68 uH.

    Compared with its neighbours in the table, HCMA1707-150-R trades 4 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 10 mOhm becomes roughly 14.1 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Confirm the terminal spacing against the rail voltage.
    • Size the saturation margin at the maximum ambient the module will see.
    • Compare against the commercial HCM row of the same size before substituting.

    Frequently Asked Questions

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products