Eaton HCMA1707-470-R 47 uH AEC-Q200 Inductor, 6.8 A
Eaton HCMA1707-470-R 47 uH AEC-Q200 Inductor, 6.8 A

Eaton HCMA1707-470-R 47 uH AEC-Q200 Inductor, 6.8 A

Share
Eaton HCMA1707-470-R: AEC-Q200 high-current inductor, 47 uH ±20%, 6.8 A Irms, Isat 7.5 A, DCR 41 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCMA1707-470-R 47 uH AEC-Q200 Inductor, 6.8 A

    HCMA1707-470-R at a glance: AEC-Q200 high-current inductor, 47 uH ±20%, 6.8 A Irms, Isat 7.5 A (20% rolloff @ +25 °C), DCR 41 mOhm, 17.5 x 17.2 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA1707-470-R
    OCL (open circuit inductance)47 uH ±20%
    FLL minimum, at Isat30.1 uH
    Irms (DC, 40 °C rise)6.8 A
    Isat (20% rolloff @ +25 °C)7.5 A
    DCR typical @ +20 °C41 mOhm
    DCR maximum @ +20 °C47 mOhm
    K-factor (Bp-p = K x L x dI)25, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10296

    Mechanical Drawing

    HCMA1707-470-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10296: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified high-current inductor on a molded powder core, rated to +125 °C. The construction is chosen for current density: the winding is pressed into the magnetic material, so there is no bobbin wasting window area and the DCR stays low for the body size.

    Copper loss at the rated current works out to roughly 1.9 W from a typical DCR of 41 mOhm at 6.8 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Stored energy at Isat is about 1,322 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 25 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,175 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    In the HCMA1707 line-up this part is number 10 of 11 by inductance, between 1.5 uH and 68 uH.

    Compared with its neighbours in the table, HCMA1707-680-R trades 3.8 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 47 mOhm becomes roughly 66.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Compare against the commercial HCM row of the same size before substituting.
    • Size the saturation margin at the maximum ambient the module will see.
    • Size the saturation margin at the maximum ambient the module will see.

    Frequently Asked Questions

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products