Eaton HCMA1707-4R7-R 4.7 uH Molded Automotive Inductor
Eaton HCMA1707-4R7-R 4.7 uH Molded Automotive Inductor

Eaton HCMA1707-4R7-R 4.7 uH Molded Automotive Inductor

Share
Eaton HCMA1707-4R7-R: AEC-Q200 high-current inductor, 4.7 uH ±20%, 27 A Irms, Isat 24 A, DCR 4.12 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCMA1707-4R7-R 4.7 uH Molded Automotive Inductor

    HCMA1707-4R7-R at a glance: AEC-Q200 high-current inductor, 4.7 uH ±20%, 27 A Irms, Isat 24 A (20% rolloff @ +25 °C), DCR 4.12 mOhm, 17.5 x 17.2 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCMA1707-4R7-R
    OCL (open circuit inductance)4.7 uH ±20%
    FLL minimum, at Isat3.01 uH
    Irms (DC, 40 °C rise)27 A
    Isat (20% rolloff @ +25 °C)24 A
    DCR typical @ +20 °C4.12 mOhm
    DCR maximum @ +20 °C4.72 mOhm
    K-factor (Bp-p = K x L x dI)76, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10296

    Mechanical Drawing

    HCMA1707-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10296: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    The family takes the molded construction used on the commercial high-current parts and applies the automotive qualification and temperature range. Soft saturation and low DCR are the two properties that matter on a 48 V or 12 V rail carrying tens of amps.

    Copper loss at the rated current works out to roughly 3 W from a typical DCR of 4.12 mOhm at 27 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 1,354 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 76 means the flux swing is about 357 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Of the 11 values listed for HCMA1707, this is the 3th, in a family covering 1.5 uH to 68 uH.

    Compared with its neighbours in the table, HCMA1707-6R8-R trades 17 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 4.72 mOhm becomes roughly 6.67 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Compare against the commercial HCM row of the same size before substituting.
    • Verify the shielding against the EMC plan for the board.
    • Size the saturation margin at the maximum ambient the module will see.

    Frequently Asked Questions

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products