Eaton HCP0805-R68-R 0.68 uH High-Current Inductor 4.5 mOhm
Eaton HCP0805-R68-R 0.68 uH High-Current Inductor 4.5 mOhm

Eaton HCP0805-R68-R 0.68 uH High-Current Inductor 4.5 mOhm

Share
Eaton HCP0805-R68-R: iron powder high-current inductor, 0.68 uH ±20%, 17.5 A Irms, Isat 25 A, DCR 4.5 mOhm, 7.9 x 7.6 mm.
    • Product Details
    • Download

    Eaton HCP0805-R68-R 0.68 uH High-Current Inductor 4.5 mOhm

    HCP0805-R68-R at a glance: iron powder high-current inductor, 0.68 uH ±20%, 17.5 A Irms, Isat 25 A (20% rolloff @ +25 °C), DCR 4.5 mOhm, 7.9 x 7.6 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCP0805-R68-R
    OCL (open circuit inductance)0.68 uH ±20%
    FLL minimum, at Isat0.44 uH
    Irms (DC, 40 °C rise)17.5 A
    Isat (20% rolloff @ +25 °C)25 A
    DCR typical @ +20 °C4.5 mOhm
    K-factor (Bp-p = K x L x dI)292, Bp-p in Gauss
    Package7.9 x 7.6 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4349

    Mechanical Drawing

    HCP0805-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4349: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    This part trades inductance per unit volume for current handling: iron powder saturates at a much higher flux density than ferrite, and the soft curve means the converter still has inductance at peak current. Standard choice for multiphase buck stages and battery power systems.

    With 4.5 mOhm typical, the I-squared-R loss at the full 17.5 A rating is about 1.38 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 212 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 292 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 199 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Positioning in the Range

    The HCP family is the iron powder, shielded, high-current range for VRM and point-of-load work. It covers modest inductance values at high DC bias, with the soft saturation curve that iron powder is chosen for.

    In the HCP0805 line-up this part is number 2 of 5 by inductance, between 0.4 uH and 2.2 uH.

    One step down the table, HCP0805-R40-R, sits at 0.40 uH with 20 A and 3.1 mOhm – the lower inductance buys about 5.5 A of extra current in the same body.

    • Core material: iron powder core, 7.9 x 7.6 mm body at 5.0 mm.
    • Typical applications: multi-phase regulators; voltage regulator modules (vrms); distributed power systems dc-dc converters; desktop and server vrms and evrds; point-of-load (pol) modules; field programmable gate array (fpga) dc-dc converters.
    • Iron powder has a soft saturation curve but a lower permeability than ferrite, so the turns count – and therefore the DCR – is higher for the same inductance.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 4.5 mOhm becomes roughly 6.36 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: at high DC bias the inductance is well below OCL. Use the inductance-versus-current curve for the ripple calculation, not the headline value.

    • Confirm the K-factor against the ripple amplitude for the core-loss estimate.
    • Account for the lower permeability of iron powder in the turns count and DCR.
    • Verify the footprint against the recommended pad layout.

    Frequently Asked Questions

    Is the part suitable for a high-frequency design?
    Iron powder suits the low-to-mid hundreds of kilohertz range. Above that the loss of the powder material rises faster than ferrite, so compare the loss curves before choosing.

    Is the part suitable for a high-frequency design?
    Iron powder suits the low-to-mid hundreds of kilohertz range. Above that the loss of the powder material rises faster than ferrite, so compare the loss curves before choosing.

    Why iron powder rather than ferrite?
    Iron powder saturates at a much higher flux density, so a small core can carry a large DC bias. The price is lower permeability, which means more turns and higher DCR for the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products