Eaton HCV1707R1-R48-R 0.48 uH Shielded Inductor 47 mOhm
Eaton HCV1707R1-R48-R 0.48 uH Shielded Inductor 47 mOhm

Eaton HCV1707R1-R48-R 0.48 uH Shielded Inductor 47 mOhm

Share
HCV1707R1-R48-R: high-current power inductor, 0.48 uH, 32 A, Isat 55 A, DCR 47 mOhm.
    • Product Details
    • Download

    Eaton HCV1707R1-R48-R 0.48 uH Shielded Inductor 47 mOhm

    HCV1707R1-R48-R at a glance: high-current power inductor, 0.48 uH, 32 A, Isat 55 A, DCR 47 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberHCV1707R1-R48-R
    Inductance0.48 nH ±20%
    DCR maximum @ +25 °C47 mOhm
    Irms (DC, 40 °C rise)32 A
    Isat55 A
    Isat268 A
    FLL minimum (at Isat)0.42 uH
    K-factor1.7
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10712

    Mechanical Dimensions & Pad Layout

    HCV1707R1-R48-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10712: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a surface-mount power inductor for DC-DC conversion. Its two limiting numbers are Irms, which sets the thermal ceiling, and Isat, which sets the current at which inductance has fallen by a defined percentage – both are on the data sheet row and both matter at different points in the load profile.

    At 32 A the winding dissipates about 48.1 W in copper, using the 47 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 55 A (68 A in the second column). Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the HCV1707R1 family this is value 1 of 1, in a range that runs from 0.48 to 0.48 uH.

    Positioning in the Range

    The power inductor family covers sub-microhenry to tens of microhenry at currents from a few amps to tens of amps, in shielded surface-mount bodies. The data sheet rows carry both typical and maximum DCR so the loss budget can be built either way.

    • DCR is quoted at +20 °C. Copper resistance rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: compatible with picor® cool-power® zvs buck and buck-boost regulator families.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three different numbers, three different checks.

    Frequently Asked Questions

    What is the difference between Irms and Isat?
    Irms is the DC current that produces the rated temperature rise. Isat is the peak current at which inductance has fallen by a defined percentage. A converter can run above Irms briefly but must stay inside Isat.

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL, not with the zero-bias value.

    What is the difference between Irms and Isat?
    Irms is the DC current that produces the rated temperature rise. Isat is the peak current at which inductance has fallen by a defined percentage. A converter can run above Irms briefly but must stay inside Isat.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products