Eaton HFW1V2815H2R2K 2.2 uH High-Current Inductor
Eaton HFW1V2815H2R2K 2.2 uH High-Current Inductor

Eaton HFW1V2815H2R2K 2.2 uH High-Current Inductor

Share
HFW1V2815H2R2K: high-current power inductor, 2.2 uH, 35.5 A, Isat 30 A, DCR 100 mOhm.
    • Product Details
    • Download

    Eaton HFW1V2815H2R2K 2.2 uH High-Current Inductor

    HFW1V2815H2R2K at a glance: high-current power inductor, 2.2 uH, 35.5 A, Isat 30 A, DCR 100 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberHFW1V2815H2R2K
    Inductance2.2 uH ±20%
    DCR maximum @ +25 °C100 mOhm
    Irms (DC, 40 °C rise)35.5 A
    Isat30 A
    SRF typical2.05 MHz
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1330

    Outline Drawing

    HFW1V2815H2R2K mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1330: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a surface-mount power inductor for DC-DC conversion. Its two limiting numbers are Irms, which sets the thermal ceiling, and Isat, which sets the current at which inductance has fallen by a defined percentage – both are on the data sheet row and both matter at different points in the load profile.

    At 35.5 A the winding dissipates about 126 W in copper, using the 100 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 30 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the HFW1V2815H2R2K family this is value 1 of 1, in a range that runs from 2.2 to 2.2 uH.

    What This Family Is For

    The power inductor family covers sub-microhenry to tens of microhenry at currents from a few amps to tens of amps, in shielded surface-mount bodies. The data sheet rows carry both typical and maximum DCR so the loss budget can be built either way.

    • DCR is quoted at +20 °C. Copper resistance rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: computing (pol/vrms); distributed power architectures; servers and workstations; lan / wan applications; game consoles.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three different numbers, three different checks.

    Frequently Asked Questions

    Why are there two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough to place parts side by side on a multiphase rail.

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL, not with the zero-bias value.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products