Eaton HPAL1V1040-100-R 10.0 uH Power Inductor, 7.8 A
Eaton HPAL1V1040-100-R 10.0 uH Power Inductor, 7.8 A

Eaton HPAL1V1040-100-R 10.0 uH Power Inductor, 7.8 A

Share
HPAL1V1040-100-R: high-current power inductor, 10.0 uH, 7.8 A, Isat 8.5 A, DCR 27 mOhm.
    • Product Details
    • Download

    Eaton HPAL1V1040-100-R 10.0 uH Power Inductor, 7.8 A

    HPAL1V1040-100-R at a glance: high-current power inductor, 10.0 uH, 7.8 A, Isat 8.5 A, DCR 27 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberHPAL1V1040-100-R
    Inductance10.0 uH ±20%
    DCR maximum @ +25 °C27 mOhm
    Irms (DC, 40 °C rise)7.8 A
    Isat8.5 A
    FLL minimum (at Isat)5.6 uH
    SRF typical12 MHz
    K-factor134
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11083

    Dimensions and Pad Layout

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 11083; the package column above gives the body size in millimetres.

    The Figures Explained

    Power inductors in this family are chosen on three numbers: inductance for the ripple, saturation current for the transient, and DCR for the loss. The data sheet gives all three against a defined test condition, which is what makes the row comparable with parts from other vendors.

    At 7.8 A the winding dissipates about 1.64 W in copper, using the 27 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 8.5 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the HPAL1V1040 family this is value 15 of 19, in a range that runs from 0.22 to 47 uH.

    Positioning in the Range

    The power inductor family covers sub-microhenry to tens of microhenry at currents from a few amps to tens of amps, in shielded surface-mount bodies. The data sheet rows carry both typical and maximum DCR so the loss budget can be built either way.

    • DCR is quoted at +20 °C. Copper resistance rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules (pol); desktop and server vrms and evrds; base station equipment.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three different numbers, three different checks.

    Frequently Asked Questions

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL, not with the zero-bias value.

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL, not with the zero-bias value.

    Why are there two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products